
To set up your @eir.net or @intred.net mailbox on an Apple device, make sure you have:
- An Apple device with the operating system updated to iOS 12
- Internet access via the Intred network or, alternatively, via a mobile data connection;
- An active e-mail mailbox. If the mailbox is not @eir.net or @intred.net, make sure you have all the necessary configuration details provided by your provider;
- The mailbox configuration details.
Specifically, the details needed to set up the mailbox are:
- POP/IMAP incoming mail server;
- Username and password;
- SMTP outgoing mail server;
- Any additional settings (SSL, authentication and ports, authenticated SMTP).
You can find your mailbox configuration details in the e-mail sent to you when your contract is activated, or in the box of the router delivered to your home (for subscriptions that include one).
FIRST SET-UP
To set up the mailbox, tap the Settings icon - Passwords & Accounts.

If you have already set up a mailbox on the device, it will appear in the list of accounts; otherwise only Add Account will be shown. Tap Add Account. A list of some of the main providers will be shown. Tap Other and then Add Mail Account.

Fill in the fields shown, entering:
- Name: your name or an identifier of your choice
- Email: the full address of your mailbox
- Password: the password associated with your e-mail address
- Description: a description of the mailbox
Then tap Next.
PROTOCOL AND PARAMETERS
You will now be asked whether you want to set up the account in IMAP or POP mode. After choosing the mode, you will need to fill in the corresponding fields. The differences between the two modes are explained below:
IMAP:
Using the IMAP protocol, e-mails are synchronised between the server and all the devices on which the mailbox is set up. As a result, any operation carried out, such as deleting an e-mail, will be synchronised between the devices and the server.
POP:
Using the POP protocol, on the other hand, e-mails are downloaded directly to the device. As a result, once an e-mail has been received, it will be saved only on the device, unless specific settings are used to keep a copy on the server. Then tap IMAP or POP, depending on the mode chosen. The images below refer to an example of configuration in IMAP mode.
INCOMING MAIL SERVER:
- Host Name: intred.net
- User Name: the full address of your mailbox
- Password: the password associated with your e-mail address
OUTGOING MAIL SERVER:
- Host Name: smtp.eir.net.
Please note that the Intred SMTP only works from an Intred line. If you also need to send e-mail over another operator’s data line, that operator must give you the SMTP parameter to enter, or you can request activation of the authenticated SMTP service; - User Name: only fill this in if you have requested the authenticated SMTP service;
- Password: only fill this in if you have requested the authenticated SMTP service.
The images below show the configurations described above. Fill in the fields with the values given above, depending on the type of SMTP you have and the mode chosen for incoming mail.

Then tap Next. The device will now connect to validate the parameters entered and create the new mailbox: this may take up to 5 minutes. During the check, an error screen may appear asking you to try setting up the mailbox without the SSL protocol. Tap Yes if this screen appears. The account set-up is complete.
AUTHENTICATED SMTP
Authenticated SMTP is an outgoing mail server that allows you to send e-mails regardless of your data line operator, except for specific blocks imposed by the operator itself. To enable this service, you need to send us an activation request at tecnico@intred.net To access the authenticated SMTP configuration menu, tap the following in sequence:
Settings - Passwords & Accounts - select the account on which to set the SMTP - Tap the account again - Tap SMTP in the OUTGOING MAIL SERVER section
Now tap the primary server (smtp.eir.net in the example) and replace the values of the server set during the first set-up with the following parameters:
- Host Name: http://smtp-auth-r.intred.it
- User Name: value given in the service activation e-mail
- Password: value given in the service activation e-mail
- Use SSL: switch off
- Authentication: password
- Server Port: 25
Tap Done for the configurations to take effect.



